CE
Conformité Européenne
SCROLL
(EU: Aerial User Equipment) CEPT Releases Draft ECC Decision (22)07 for LTE and 5G Use by Aerial User Equipment
The European Conference of Postal and Telecommunications Administrations (CEPT) has recently published a draft of ECC Decision (22)07, which sets out proposed technical and operational conditions to enable aerial user equipment (aerial UEs)—such as drones—to operate on LTE and 5G mobile networks.
The primary objective of the draft decision is to prevent harmful interference that may arise when aerial UEs operate in frequency bands originally designed for terrestrial mobile services. The draft identifies the following frequency bands as within scope:
- - 703-733 MHz
- - 832-862 MHz
- - 880-915 MHz
- - 1710 - 1785 MHz
- - 1920-1980 MHz
- - 2500-2570 MHz
- - 2570-2620 MHz
The document indicates that additional conditions may be introduced for aerial UEs in future, including Out-of-Band Emission (OOBE) limits and geographically defined no-transmit zones, depending on regional deployment scenarios.
Reference: Draft revision of ECC Decision (22)07(EU: SRD) Planned Update to Short Range Devices (SRD) Frequency Regulations in Europe
An update is planned for ERC Recommendation (70-03), the key European regulatory document governing frequency usage for Short Range Devices (SRDs).
As part of the forthcoming revision, the following additions are expected:
- Annex 6 (Radiodetermination):
Inclusion of provisions for operation in the 76.5–80.5 GHz frequency band. -
Annex 6 (Radiodetermination):
Inclusion of provisions for operation in the 76.5–80.5 GHz frequency band.
These updates are intended to reflect evolving technologies and emerging use cases, while ensuring continued harmonization of SRD spectrum usage across Europe.
Reference: ERC Recommendation (70-03)(EU:WBB LMP) ECC Issues Recommendation (25)03 on Protection of FS and FSS for WBB Systems in the 3800–4200 MHz Band
In November 2024, the Electronic Communications Committee (ECC) adopted ECC Decision (24)01, allowing the introduction of low/medium power terrestrial wireless broadband systems (WBB LMP) in the 3800–4200 MHz frequency band. However, concerns were raised that the Decision alone did not provide sufficient technical measures to ensure adequate protection of existing Fixed Service (FS) and Fixed Satellite Service (FSS) operations.
To address these concerns, ECC subsequently published ECC Recommendation (25)03, which complements Decision (24)01 by introducing additional technical guidance focused on coexistence and protection mechanisms.
FS systems, which rely on highly directional point-to-point links, can be immediately impacted by interference. In contrast, FSS systems—due to their low elevation angle links directed toward satellites—may be affected even by weak terrestrial emissions originating from distant sources. These characteristics necessitate carefully defined protection areas.
Accordingly, ECC Recommendation (25)03 provides methodologies for determining coordination contours and exclusion zones, taking into account the differing interference sensitivities of FS and FSS systems, while maintaining the regulatory framework established by ECC Decision (24)01.
(EU:WPT) Update to ECC Recommendation (25)01 on Wireless Power Transmission Emission Limits
In February, the Electronic Communications Committee (ECC) published ECC Recommendation (25)01, which defines emission limit requirements for Wireless Power Transmission (WPT) systems.
The Recommendation specifies limits for both operating emissions and unwanted emissions associated with non-beam Wireless Power Transmission (WPT) technologies. At present, its scope applies to generic WPT applications, including medical implantable devices, as well as portable and mobile devices.
An update scheduled for October 2025 introduces minor editorial changes, such as clarifications to the notation and presentation in Annex 1. No changes have been made to the regulatory scope, emission limits, or underlying policy framework of the Recommendation.
RED CA
From 5 to 6 November, the 50th RED Compliance Association (RED CA) Meeting was held in Greece. The key discussion points are summarized below for your reference.
(EU: CRA ) Cyber Resilience Acts
At the 50th RED CA Meeting, extensive discussions were held on the Cyber Resilience Act (CRA), the European Union’s new cybersecurity legislation.
The CRA is an EU regulation established to strengthen the cybersecurity of hardware and software products. It imposes cybersecurity obligations on manufacturers, importers, and distributors throughout the entire product lifecycle, from development and market placement to post-market maintenance.
In particular, manufacturers are required to conduct risk assessments, comply with Essential Security Requirements, implement vulnerability handling processes, and fulfill incident and vulnerability reporting obligations.
The CRA will apply broadly to hardware products such as CPUs, network equipment, smart appliances, and components, as well as software products including operating systems, libraries, mobile applications, and games. In addition, Remote Data Processing Solutions are also within scope.
Conformity assessment will be determined based on product criticality, either through self-assessment or assessment by a Notified Body (NB). For certain important and critical products, the introduction of a certification scheme is planned at a later stage.
During the RED CA Meeting, the differentiated conformity assessment approach by product category was explained, along with the introduction of mandatory reporting obligations for vulnerabilities and security incidents. Manufacturers will be required to report product defects or cybersecurity incidents and to continue reporting all relevant information until corrective actions have been fully completed.
The CRA will become mandatory as of 11 December 2027. Horizontal standards are scheduled to be issued by August 2026, followed by vertical standards by October 2027. It was also announced that a dedicated organization or department will be established to support the application of the standards and to address CRA-related inquiries.
(EU: Cyber TGNs) TGN Update_TGN35, TGN36, TGN37
The European Union announced that it plans to issue TGN 35, TGN 36, and TGN 37 as guidance documents to support the interpretation of the cybersecurity requirements set out in Article 3.3(d) to (f), which have been mandatory since August.
| TGN | SCOPE | RED ARTICLE |
|---|---|---|
| TGN 35 | USB, Ethernet, dongles, or other devices that are capable of communication | Article 3.3(d)_ Network protection |
| TGN 36 | Children’s toys, wearables, tracking | Article 3.3(e)_ Privacy protection |
| TGN 37 | payment, money transfer, payment authorization | Article 3.3(f)_ Anti-fraud |
These guidance documents are expected to provide clarifications on the scope of application and relevant product categories for each Article, as well as details on the documentation required for conformity assessment and certification.
(EU: USB-C Type) Expansion of the Scope of Article 3.4 – Common Charger
The Common Charger requirements under Article 3.4 are currently in force, and the European Union announced that it is reviewing a potential extension of the scope of applicable devices. The key objectives of this initiative are as follows:
- Enhancing user convenience, by preventing the use of different chargers for each device and by allowing consumers to purchase devices without a charger
- Reducing electronic waste (e-waste)
During the recent RED CA Meeting, the EU presented the results of a study on the possible expansion of the scope to radio equipment using wired charging, which was conducted following the scope extension announced in May.
The following product categories are under review, with a report expected to be submitted by 28 December:
- Wearables
- Radio-controlled toys
- Drones
- Electric toothbrushes
- Virtual reality headsets
- Video game controllers
In addition, the EU shared the publication schedule for new USB specifications.
| USB-IF Publication - USB Type-C Cable and Connector Specification (USB Type-C Spec R2.4 - October 2024) | 28 October 2024 |
| USB-IF Publication - USB Power Delivery Specification (USB PD R3.2 V1.1 2024-10) | 11 September 2024 |
| IEC Publication (62680-1-2 and 62680-1-3:2024) | 13 December 2024 |
| CEN-CENELEC Ratification (62680-1-2 and 62680-1-3:2025) | 17 January 2025 |
| CEN-CENELEC Availability (62680-1-2 and 62680-1-3:2025) – Published | 31 January 2025 |
| CEN-CENELEC Publication (62680-1-2 and 62680-1-3:2025) | 31 January 2026 |
Changes to charging power labelling requirements were also announced:
- Radio equipment: charging power indication of 15–45 W will be applied
- External Power Supplies (EPS): charging power indication of 45 W will be applied
- A future amendment through a Delegated Act is planned to align the Ecodesign EPS regulation with the labelling requirement