본문
기술칼럼
Technical column
SCROLL
2025 October TCBC Workshop 주요 내용 Summary
지난 10월 21~22 일에 2025 October TCBC Workshop 이 개최되었습니다. 주요 내용을 요약하여 안내 드리오니, 참고해주시기 바랍니다. 다른 섹션에서 언급된 내용 외의 내용을 주로 다루고 있음을 참조 바랍니다.
이번 TCBC Workshop 은 미국 정부의 Shutdown 기간에 진행이 되었기 때문에, 대부분의 FCC 관계자는 참석하지 못했고, FCC 소속 National Security Counsel 에서만 참석하여, “Bad Labs” 이슈에 대한 개요 설명과 질의 응답 위주로 세션이 진행 되었습니다. 해당 사안과 관련하여 FCC 는 추후 별도의 Webinar 를 진행할 예정이라고 하니 업무 참조 바랍니다.
(미국: ) “Bad Labs”
- Current Published Policy
- Prohibited Entity 가 10% 이상의 지분을 보유하고 있으면, FCC 인가 시험소 및 TCB에서 제외
(현재, 11개 시험소에 대해 FCC 가 조치) - 모든 TCB 및 시험소는 5% 이상 지분에 대한 보고 및 비소유 인증 필요
(OMB (The office of Management and budget) 검토로 해당 요구 사항 시행 대기 중) - Modular Transmitter 도 Covered equipment 에 포함
- Prohibited Entity 가 10% 이상의 지분을 보유하고 있으면, FCC 인가 시험소 및 TCB에서 제외
- Current Published Policy not applied
- Foreign Adversary (중국, 러시아, 이란, 쿠바, 홍콩 등) 소재의 시험소에 대한 시험 금지
- TCB 와 시험소 소유권 분리 (TCB와 동일 소유 구조에 시험소에서 시험한 Application 리뷰 불가)
- TCB 사후 관리 시험을 다른 TCB 에서 인증 낸 것만 할 수 있음
- SDoC 에 대해서 시험소 인가 의무 부여 (현재 FCC 내부 검토 중)
(미국: ) “Data Referencing”
FCC의 경우, 모든 transmitter가 포함된 Parent device(full testing을 수행한 기준 모델)에서 일부 transmitter가 제거된 Variant device(Parent model에서 일부 RF 부품이 depopulation된 모델)에 대해, 변경되지 않은 RF 경로 및 회로 부분에 한하여 동일성 검증(justification)을 통해 시험 데이터(data referencing)를 재사용할 수 있는 절차가 있습니다.
해당 Data referencing 제도는 TCBC Workshop을 통해 최근 정책 변화 및 적용 범위에 대해 하나의 아젠다로 다루어졌습니다.
- FCC KDB 484596 D01 v02r01 – Oct 23, 2023
- • Requires an ECR (Equipment Compliance Review) procedure to receive FCC`s confirmation
- • Allowed: Variations due to population, or depopulation or replacement of components
- • Certification: Can be new FCC ID or a variant within the same FCC ID (C2PC)
- • Must all be within the same Grantee code
- FCC KDB 484596 D01 v03 – March 21, 2025
- • Back to stricter times, and not so many changes permitted
- • Reference device must be the most fully populated, Variant can only have transmitter de-population
- • No Data reference under the same FCC ID permitted
- • All tests require a spot-check to confirm the justification in the test plan
- • ECR removed, all decision now made by the TCB
KDB 484596 D01 v03 업데이트에 따라, Variant 모델에서 RF 부품이 population되는 경우, 데이터 레퍼런싱(Data Referencing)의 적용에 제약이 있을 수 있습니다. 따라서, 해당 사항에 대해서는 KDB Inquiry를 통해 FCC의 추가적인 해석 및 확인이 필요 할 수 있습니다.
(캐나다: ) RSS-248, “Permanently Integrated Antenna”
ISED 의 RSS-248 규격에서 Low Power Indoor AP, VLP, Indoor subordinate device 는 Permanently integrated antenna 가 요구 되는데, 가능한 범위에 대해 안내 하였습니다.
- Permanently attached antenna
- Unique proprietary connector
- Standard connectors with authentication protocol
(단, Reverse connector 의 경우에는, 시중에서 구매 가능하거나, 인터넷에서 유통되는 형태의 Reverse connector 는 허용 안 됨)
만약, Unique connector 및 Authentication 을 적용 하는 경우에는 미리 ISED 에 Inquiry 가 필요 합니다.
KDB Sharing
FCC 와 ISED 의 경우, 해당 홈페이지를 통해 기관에 직접 서면으로 문의 및 답변이 가능하며, 이 중에 같이 공유할만한 사항들이 TCBC 에서 소개가 되었습니다.
1) FRL Calculation (ISED)
[Question]
May I have your guidance on how to provide the correct information to the Spectra system for FRL [Field Reference Level] when this document is generated by the manufacturer themselves?
[ISED Answer]
Please note that FRL calculations can be completed by the client but they must be verified by an ISED recognized test lab. There is no scope for FRL, therefore, any recognized lab can perform this verification. The CN of the test lab needs to be recorded in the field [GC: in Spectra, when uploading the application]
2) SAR Values Reported in Spectra (ISED)
[Question]
When filling out RSS-102 Annex A, should the SAR values reported in RSS-102 Annex A (and therefore, those listed in spectra) be standalone values or simultaneous transmission values? We’ve seen that not all CBs do this in the same way.
[ISED Answer]
Please note that ISED only requires standalone SAR values to be reported.
3) N.S Testing in a C1PC (ISED)
[Question]
We have been approached by a grantee who obtained IC certification for a proximity reader that operates at both 125 kHz and 13.56 MHz in 2015, prior to the requirement for N.S. testing. They would now like to upgrade the firmware in the device (no changes to the authorized emissions) and give it a new HVIN, hence, a Class I Permissive Change would be required.
My questions are, in this situation, would N.S. Testing now also be required for the 125 kHz emission? And, if so, would it still be considered a c1pc, with the inclusion of N.S. data?
[ISED Answer]
All the current RSS requirements for the product are applicable. Any testing that was not performed and reported to ISED must be performed and reported to ISED according to the latest issue of applicable RSSs
4) Modifications to non-U.S. transmitter (FCC)
[Question]
A device was certified with a WiFi transmitter, and, also included in the EUT is a second 2.4 GHz transmitter that is only authorized for use in the EU - it is disabled at the factory in all units being marketed in the U.S. The applicant has now had to change the non-U.S. transmitter to a similar, but not identical version due to EOL of the original, in other words, it is not pin-for-pin compatible with the original (non-U.S.) transmitter chip. As a result, there has been a pcb re-layout, also accommodating some modified digital circuitry within the EUT (again, not related to the WiFi operation). My question is, may this modification to the non-U.S. approved transmitter portion of the device be accomplished via permissive change (Class 1 or Class 2, depending on test results) to the certified WiFi transmitter? Or must a new FCC ID be obtained for the WiFi transmitter, even though the modifications are to the non-U.S. certified transmitter portion of the device? Just to be clear, there have been no modifications at all to the certified WiFi circuitry and trace antenna. The only modifications are to the non-U.S. certified transmitter and some digital circuitry within the device.
[FCC Answer]
Yes, this modification would be permitted via permissive change.
5) FCC ID number on US Agent for Service of Process Attestations (FCC)
[Question]
We recently received an RT from the FCC in which you stated that the US Agent for Service of Process attestation letter must be revised to also list the FCC ID number of the application with which the attestation was submitted.Is this a new requirement?Until now, the FCC has only required that the FRN and grantee code be included in the letter, allowing an applicant to re-use the same letter for multiple applications.Please clarify if this policy has now changed.
[FCC Answer]
It is a recommended best practice to put the FCCID on the Agent for Service of Process certification but it is not a mandatory requirement. See KDB986446question 20 for information related to this issue.
6) Bandedge compliance of non-straddle channels in NII bands (FCC)
[Question]
Are devices supporting both NII-2C, NII-3, and the straddle frequencies in between required to show compliance to the frequency edge between NII-2C and NII3?
The question is for frequencies in
non-straddle channels in UNII-2C (i.e. CH140, 5700 MHz, 20 MHz BW) if they can follow the band edge requirements at edges 5.85 GHz and no longer at 5.725 GHz (same provision given for the straddle channels per B.2.b)(iii)).
Or are UNII-2C ch 140 5700 MHz signals only eligible for band edge compliance to the 5.725 GHz band edge regardless if straddle channels between 2C/3 exist?.
[FCC Answer]
Regardless if straddle channels exist, 802.11 CH 140 must meet the band edge compliance to the U-NII-2C band.
HAC Waiver and New Test Procedure
HAC (Hearing Aid Compatibility) 는 보청기 호환성 시험으로, 통화 기능이 있는 제품의 경우 HAC 를 만족해야 합니다. 해당 시험에 대한 시험 방법에 대한 이슈가 있어, 국가별 현재 상황과, 이를 해결한 규격 개발 현황에 대해 소개 되었습니다.
- Current Situation
- FCC - DA 25-759 (Aug 2025) extends HAC Waiver until Sept 29, 2027 or until new Volume control standard available
- ISED – RSS-HAC Amd 2 (June 2025) compliance required by Jan 1, 2028 (No Grandfathering)
- 현재의 PN-SDNR(Pulsed Noise Signal to Distortion and Noise Ratio) 방식이 현대의 Codec 및 AI 노이즈 캔슬링 기술 등과 호환이 잘 되지 않음.
- Standard Development Progress
- Distortion Test Method(Volume Control)변경
- PN-SDNR Δ-POLQA, ETSI-STQ Nonlinearity Measurement(NLM)
- ✓ Δ-POLQA: MOS 수학적예측 알고리즘, Full-Band(20kHz) 가능, 주파수 응답 및 왜곡 동시평가, 최신 오디오 코덱 및 AI 기반 음성개선 알고리즘과 호환
- ✓ ETSI-STQ Nonlinearity Measurement(NLM): ETSI TS 104 063사용, Python Code 제공, 결과(dB, %), AI
- Progress status
- ✓Test Plan development (In progress) → Round robin testing (2025 Q4) → Acceptance Criteria (Q1 2026) → ANSI Balloting & approval (Q2 2026)
ANSI C63.10 Transitions
지난 HCT Insight, Issue 23 의 ISED 03 관련 기사에서 소개드린 바와 같이, Unlicensed Wireless Devices 에 대한 측정 방법인, ANSI C63.10 의 업데이트 적용이 단계별 시행 예정 입니다. 현재 ANSI C63.10-2013 규격은 사용이 불가한 상황(2025년 9월 12일 이후) 이며, 그 외에도 하기와 같이 적용 예정 입니다.
- 2026년 1월 6일까지 적용 가능한 규격
- ✓ ANSI C63.10-2020+Cor.1-2023
- ✓ ANSI C63.10-2020+Cor.1-2023+C63.10a-2024+Errata to C63.10a-2024
- 2026년 1월 6일이후 적용 가능한 규격
- ✓ ANSI C63.10-2020+Cor.1-2023+C63.10a-2024+Errata to C63.10a-2024
해당 규격 변경에 따라, 캐나다에 판매, 유통, 생산, 마케팅 등 이 해당 일자 이후에도 계속 되는 제품은 최신 규격에 만족 하도록 판매가 되어야 하며, 해당 규정 만족이 안 되는 경우, 관련 Permissive Change 의 적용이 필요 할 수 있습니다.
5600-5650 MHz TDWR Band in ISED
RSS-247 Issue 4가 발행됨에 따라, ISED에서도 5600–5650 MHz 대역의 사용이 가능해졌습니다.다만, 해당 대역에 대한 DFS 시험 시에는 EN 301 893 V1.8.1에 정의된 Radar Signal을 사용해야 합니다.
Access Point의 경우, 해당 대역을 사용하고자 할 때 DFS 시험 수행 및 C3PC 신고가 요구되며,Client 기기의 경우, 인증서에 해당 주파수 대역을 반영해야 하는 경우를 제외하면 별도의 신고나 추가 시험은 필요하지 않음을 ISED가 명확히 하였습니다.
그 외의 다른 TCBC workshop 이슈 들은 해당 뉴스레터의 다른 페이지(FCC/ISED issue 등) 에서 자세하게 다루고 있으니, 해당 내용 참조 바라며, 그 외의 전체 TCBC Workshop 내용이 궁금하시거나, 세부 내용을 알고 싶으신 분께서는 하기 HCT 로 언제든 연락 바랍니다.